Sometimes a job starts small. A homeowner calls about a light fixture that stopped working, and the diagnostic turns up a loose neutral feeding half the circuit. A landlord calls about an outlet that tripped the GFCI, and the panel behind it turns out to be a 100-amp box already running at capacity. That is the work we do in East Haven every day: we start where the symptom is and follow it back to the actual cause. When the job turns out to be bigger than the call described, we explain what we found and what it means before anything else happens.
We handle residential and commercial electrical work across East Haven, from routine repairs and outlet replacements to panel upgrades, rewiring, and new circuit installations. We are available every day from 7:00 AM to 10:30 PM.
Call (475) 366-2995 for a quote.
Scheduling is straightforward. You call, we talk through what you are seeing, and you get a price before anything is booked. The scope and the rate are confirmed on the phone, so there are no open questions by the time we show up.
For a problem that will not keep, we take short-notice calls. If a breaker will not reset, an outlet is warm to the touch, or there is a burning smell near the panel, that is not a situation to sit on. Call during our hours and we will work out what the schedule allows.
For rental properties and businesses that have to stay open, we plan around the space. That means confirming ahead of time which circuits will be out of service and for how long, so tenants and staff are not caught off guard. The scope is worked out before the visit, not figured out at the door.
A lot of the wiring in older East Haven homes runs through spaces that were never designed for easy access. Attics with low clearance, crawl spaces with no flooring, and wall cavities that have been insulated over the original wiring all change how a job gets planned. We account for access before we quote, so the price reflects what the job actually involves.
High ceilings and finished rooms add time to lighting and fan work. Getting a fixture into a cathedral ceiling or running a new circuit through a finished wall without tearing it apart takes more planning than a standard installation. We'll find the fault and fix it right, whether that means working around the finish or opening only what needs to be opened.
A welder, an air compressor, or a workshop tool running off a shared circuit is a problem waiting to happen. These loads need a dedicated circuit sized to the equipment, with the wire gauge and breaker rating matched to what the tool actually draws. The same applies to an electric range, a wall oven, or a dryer: each needs its own circuit, and running one off an existing shared line is a common cause of repeated trips and overheating at the connection point.
A generator that is plugged directly into the house without a transfer switch creates a backfeed risk to the utility line. A transfer switch is what makes the hookup safe. We install manual and automatic transfer switches, run the circuit from the panel to the generator connection, and confirm the load the switch is rated to carry. For properties in this region where a Nor'easter can take out power for several days, having the connection done correctly is the difference between a generator that works when it matters and one that sits in the garage.
Homes built in the 1960s and 1970s often have aluminum branch wiring, and the problem is not the wire itself but what happens at the connections over time. Aluminum expands and contracts differently than copper, and terminations at outlets, switches, and fixtures can loosen in ways that cause overheating. Remediation involves replacing or retrofitting those connection points with materials rated for aluminum, and it is often flagged during a home sale inspection or an insurance renewal. We work through the scope section by section and explain what we find before any work is authorized.
Outdoor lighting work covers more than swapping a fixture. Running a new circuit for security lights, installing motion sensors, or wiring a landscape lighting system from the panel all involve weatherproof connections, proper conduit, and a circuit that can carry the load. We take pride in the electrical work we leave behind, which means the conduit is run cleanly, the connections are weatherproofed correctly, and the switch or timer operates the way it should.
The rate is confirmed on the phone before anything is scheduled. What moves a quote is the fault itself, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change being made. A straightforward outlet repair and a partial rewire are different jobs, and the price reflects that difference.
No-pressure estimates, priced up front, so you know what the visit covers before we arrive. If the diagnostic turns up something that changes the scope, we explain it before we proceed. The scope of the electrical work is priced before it starts, and nothing gets added without a conversation first.
A few things that commonly affect what a job costs:
Local permit rules decide which electrical jobs need an inspection. Panel replacements, service upgrades, and new circuit installations in Connecticut typically require one. We confirm what applies to your specific job before the work starts, so the permit process does not catch anyone off guard.
On a renovation or an addition, the order of trades matters. Framing has to be in place before circuits can be run, but the electrician needs to be on site before the walls are closed. If the rough-in is missed, the only way to add a circuit later is to open the wall back up or fish wire through finished drywall, which adds time and cost to a job that did not need either.
The same issue comes up on kitchen and bathroom remodels. A new layout often means moving circuits, adding a dedicated line for the range or dishwasher, and confirming the panel can carry the load before the countertops go in. Getting the electrical scope confirmed early means the rest of the project does not have to stop and wait.
We work with general contractors and individual property owners on phased projects. The conversation about what the electrical side needs happens at the planning stage, not after the drywall is up. Reach out and we'll get it diagnosed.
We cover East Haven and the communities around it in New Haven County. That includes Branford, Branford Center, New Haven, West Haven, and North Haven. Residential and commercial calls are welcome from anywhere in the area, whether the job is a single circuit repair or a full panel upgrade on a multi-unit building.
If you are not sure whether we reach your address, a quick call will confirm it. Everything covered is listed on our full list of electrical services.
Stop using the outlet or the circuit immediately and do not reset the breaker if it has tripped. A burning smell near an outlet, switch, or panel points to a connection problem or a fault that can cause overheating, and it is not a situation to leave until a more convenient time.
Call (475) 366-2995 during our hours, describe what you are seeing and smelling, and we will work out how quickly it needs to be looked at.
Labeling the panel is part of finishing the job correctly. If we add or modify circuits, we label them at the panel so the breakers correspond to what they actually control. If the existing panel labels are incomplete or inaccurate, we note that and can update them as part of the visit. A panel that is correctly labeled is one you can actually use in an emergency.
Not always. In some cases wire can be fished through a finished ceiling without opening it. Whether that is possible depends on the construction of the ceiling, where the new wire needs to go, and what is already in the space above. We assess the construction before we commit to an approach and tell you what the options are, including what each one means for the ceiling finish.
Permit requirements depend on the type of work. Panel replacements, service upgrades, and new circuit installations typically require a permit and a follow-up inspection in Connecticut. We confirm what applies to your specific job before the work starts, pull the permit where it is required, and factor the inspection into the project timeline. You do not have to manage that process separately.
When the panel is in a shared utility space, a basement, or a locked room that belongs to the building, access has to be arranged through whoever controls that space. We identify that on the call and make sure the right person knows to provide access before we arrive. A visit where the panel is unreachable is a visit that cannot be completed.
Rewiring a finished space typically requires opening walls or ceilings at certain points to run new wire, and those openings are left ready for a drywall finisher and painter to close. We are not a drywall or painting trade, so patching and finishing are handled separately. We keep openings to what the work requires and explain what will need to be addressed cosmetically before we start.
Yes. A single dead outlet, a switch that needs replacing, or a ceiling fan that needs to be wired in is worth a call. Small jobs are part of what we do, and leaving a known problem in place because it seems too minor to schedule often leads to a larger problem later.
Call (475) 366-2995 and describe what needs attention.
It depends on what was done and what code requires. Some homeowner installations can be corrected at the connections or brought into compliance with targeted repairs. Others have to come out because the wiring method, the box fill, or the circuit protection does not meet current standards. We assess what is there and tell you what the options are before recommending a course of action.
Older housing stock in this part of New Haven County tends to produce a predictable set of issues: panels that were sized for a lighter load than the home now carries, outlets and switches on circuits that have been extended or modified over the years, and wiring that predates current arc-fault and ground-fault requirements. Knob-and-tube and aluminum branch wiring both come up regularly during diagnostics and home sale inspections. A call about one symptom sometimes opens into a broader conversation about what the wiring behind it looks like.
We power your home. We protect your circuits. We earn the call.
Call (475) 366-2995 and you reach someone who knows the trade and can scope the job on the phone.
The price is confirmed before anything is scheduled. We are available every day from 7:00 AM to 10:30 PM.
See the whole of our list of communities. Wiring and panel work nearby: New Haven, West Haven, North Haven, Milford, Wallingford.
Every electrical job we take on starts with a clear scope and a price confirmed before any work begins. The table below covers the services we handle most often across East Haven and the surrounding area, what each one involves, and who it fits best. Whether you are dealing with a fault that showed up overnight or planning an upgrade you have been putting off, this gives you a plain-language starting point before you call.
| Type of Work | What's Included | Best For | What to Keep in Mind |
|---|---|---|---|
| Electrical Panel UpgradesMost Popular | 100-to-200 amp service upgradesFuse box to breaker panel conversionSubpanel installationLoad calculation before work begins | Older homes with undersized service, or any property adding significant new electrical load | Panel replacements require a permit and inspection in Connecticut. We factor that into the scope and price on the call so nothing is left open-ended. |
| Electrical Repairs & Troubleshooting | Fault tracing from symptom to sourceOutlet and switch testingCircuit and panel checksRepair once cause is confirmed | Any home or property with an unexplained electrical problem | The fault is traced before anything is replaced, so you are not paying for parts that were not the problem. |
| Lighting Installation | Recessed and LED can lightingExterior security and motion lightsFixture and pendant replacement | Rooms being updated, new construction spaces, and outdoor areas needing security coverage | New lighting circuits can be added where none exist. We confirm panel capacity before running new wire. |
Call (475) 366-2995 to talk through what you are seeing and get a price before anything is scheduled.
(475) 366-2995