Property managers, contractors, and building owners in New Haven deal with electrical problems that do not wait for a convenient time. A tenant reports a dead circuit on a Friday afternoon. A renovation stalls because the panel cannot carry the new load. A commercial space needs a dedicated circuit before equipment can go in. We handle all of it, residential and commercial, from a single outlet replacement to a full service upgrade, and we are available every day from 7 AM to 10:30 PM.
New Haven's housing stock runs the full range, from triple-deckers and multi-unit buildings near the city center to older single-family homes where the wiring has been added to and modified over decades without a clear record of what was done. That variety shapes the calls we take. We work across all of it, and the scope of every job is confirmed before anything starts.
Every electrical call starts with a situation, not a catalog entry. Here is what those situations look like and what the work actually involves.
A breaker that trips under load, a circuit that loses power only in certain conditions, or a fault that shows up once and then disappears are all harder to fix than a dead outlet, because the problem has to be caught in the act. We trace intermittent faults through the circuit from the panel outward, testing connections, checking load, and looking for the conditions that produce the failure. Finding it is its own job, and it gets done before anything is replaced.
Connecting a generator to a home's panel without a transfer switch creates a backfeed risk that is dangerous to anyone working on the utility line. We install manual and automatic transfer switches and run the dedicated circuit from the panel to the connection point. The load the switch is sized to carry is confirmed before the installation is scoped.
A new electric range or a dryer that is moving to a different location in the house needs a dedicated 240-volt circuit sized for the appliance. We run the circuit from the panel, confirm the panel has the capacity to carry it, and install the outlet or hardwired connection. If the panel is already at capacity, that conversation happens before any wire is pulled.
Outlet and switch replacement covers more than swapping a receptacle. GFCI protection is required in kitchens, bathrooms, garages, and exterior locations, and AFCI protection applies to bedroom circuits in most current code. We install both where they are required and where they add meaningful protection in older wiring. Ceiling fan installation starts with confirming the ceiling box is rated for a fan's weight and motion, since a standard fixture box is not, and includes the wiring and switch configuration the fan actually needs.
A detached garage, a workshop, or an electric gate at the end of a driveway needs its own supply run from the main panel, often with a subpanel at the far end to keep the circuit lengths manageable. We scope the run, confirm the panel has the capacity, and size the subpanel for what the space will actually carry, including any future load the owner is planning for.
A hot tub, a workshop compressor, or a large piece of kitchen equipment draws more than a standard circuit was designed to carry. We install the dedicated circuit, confirm the disconnect requirements, and check whether the existing panel can support the added load before anything is connected. Electrical work here is done to the code this area actually enforces.
The pricing conversation happens on the phone before anything is booked. You describe what you are seeing, we talk through the scope, and you get the rate before a visit is scheduled. No-pressure estimates, priced up front. We are available every day from 7 AM to 10:30 PM, including weekends, which matters when a tenant's problem cannot wait until Monday.
For rental units and commercial spaces that have to stay open, the visit is scoped around what the property needs. A business that cannot shut down a circuit during business hours gets a different approach than a vacant unit being turned over between tenants. We confirm what the schedule allows on the call so the visit does not create a problem it was not sent to solve.
Intermittent electrical faults are the hardest calls to diagnose because the fault is not always present when someone is looking for it. A breaker that trips only when the air handler and the microwave run at the same time is telling you something about load, not about a failed component. A circuit that loses power in wet weather is pointing to a connection problem that moisture is making worse. A light that flickers only after the house has been running for a few hours may be showing a thermal issue at a connection that tightens and loosens as it heats and cools.
These faults do not announce themselves clearly, and replacing the most obvious part rarely fixes them. We trace the symptom through the circuit, test under the conditions that produce it where we can, and confirm the actual cause before any repair is made. We'll find the fault and fix it right.
Older multi-unit buildings and single-family homes in New Haven were wired for a fraction of the electrical load a modern household or business places on a panel. Adding a Level 2 EV charger, a second HVAC disconnect, or a commercial kitchen circuit to a building that was never sized for it is not simply a matter of running wire. The panel has to be assessed first.
We run a load calculation to confirm what the existing service can carry and what the new demand will add. If the panel has the capacity, we run the circuit and confirm the disconnect requirements. If it does not, the options are a panel upgrade, a subpanel to distribute the load, or a service entrance upgrade if the meter and main need to come up to current standards. The scope and the options are laid out before any work begins, so the decision about how to proceed is the customer's to make with a clear picture of what each path involves.
Whole-home surge protection fits into this conversation too. A panel-level surge protector covers every circuit in the building from a single installation point, including the disconnects for HVAC equipment, the refrigerator, and the electronics. For buildings where the wiring has been extended and modified over decades, it is a practical addition to any panel upgrade.
On a renovation or a build-out, the electrician needs to be on site before the walls close. That sounds obvious, but the sequence breaks down regularly when trades are scheduled independently. Rough-in wiring, junction box placement, and panel capacity all have to be resolved while the framing is accessible. A ceiling fan location that gets decided after the drywall goes up costs more to wire than one that was planned before it.
The most common problem is a panel that cannot carry the load the renovation adds. A kitchen remodel that adds a dishwasher, a range, and under-cabinet lighting on top of an existing 100-amp service is a panel upgrade conversation, not just a wiring job. When that is discovered after the kitchen is finished, the remediation is more disruptive and more expensive than it would have been if the load calculation had been done at the start. We work with contractors and property managers to confirm panel capacity before the build begins, so the electrical side does not become the reason a project stalls.
The price for electrical work is not set by the size of the property or the number of rooms. It is set by the scope of the specific job. What the fault turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change are the three things that move a quote up or down.
A straightforward outlet replacement in an accessible location is a different job from tracing a fault through a finished wall to find a connection that has been failing for years. A dedicated circuit for a new appliance is a different job if the panel has two open slots versus one that is already at capacity. We scope the job on the call, confirm the rate before scheduling, and explain what is included. If the visit turns up something that changes the scope, that conversation happens before any additional work is authorized.
The scope of the electrical work is priced before it starts. That is how the call works, and it is what you should expect when you phone.
We work throughout New Haven and cover the surrounding communities in New Haven County. That includes West Haven, East Haven, Orange, Woodbridge, and the areas nearby. Residential calls, rental property work, and commercial electrical jobs are all welcome from anywhere in the area.
If you are not sure whether we cover your address, a call will confirm it. The same availability, the same pricing process, and the same scope of work apply across the whole service area. Start with the page listing our electrical services if you want the detail before the call.
Yes, in practical ways. Pre-1960s construction in this area commonly turns up knob-and-tube wiring, ungrounded circuits, and panels that were sized for a fraction of the load a modern building carries. Newer construction has its own issues, including aluminum branch wiring from the 1960s and 1970s and panels that were sized for the original layout rather than the way the space is used now. The diagnostic visit covers what is actually there, not what the age of the building suggests should be there.
A burning smell from an outlet or panel, sparking at a receptacle, a breaker that will not stay reset, or a complete loss of power with no obvious cause are all situations worth calling about right away. Leaving a live fault in place overnight raises the risk of it getting worse.
Call (475) 366-2995 and describe what you are seeing so we can assess how urgent it is.
A buyer who wants an electrical inspection before closing can arrange one, and we can conduct the inspection and provide a written report on what we find. The report describes the condition of the system and what any deficiencies would involve to correct. Whether the seller has to consent to access is a matter between the buyer and seller, not something we control.
Framing needs to be complete, the panel location needs to be confirmed, and any chases or conduit runs that go through concrete or masonry need to be in place. If the service entrance or panel is being relocated, that has to be settled before wire is run. We walk through what needs to be in place during the scoping call so the rough-in visit is not delayed by something that could have been sorted earlier.
Yes. Rough-in and trim-out are two separate visits. After the walls are closed and finished, we return to install the outlets, switches, fixtures, and covers, and to make the final connections that bring the circuits live. The trim-out visit is scheduled as part of the original scope so it does not get lost in the renovation timeline.
Yes. We scope the visit around what the property needs and confirm on the call what the schedule allows. For a rental unit with a tenant in place, we work through what needs to be accessed and what the tenant should expect. For a commercial space that has to stay open, we confirm which circuits can be taken down and when before the visit is scheduled.
We tell you on the visit what needs to be ordered and how that affects the timeline for completing the work. Where it is safe to do so, we leave the existing system in a usable state while the part is sourced. We confirm the follow-up visit before we leave so the job does not sit open-ended.
The most useful thing is a clear description of what the project adds to the building: new appliances, additional circuits, a panel in a new location, or a supply to a detached structure. That information lets us scope the panel capacity question on the call and come to the site prepared for the load calculation. You do not need drawings or specifications. Describing what the finished space needs to run is enough to start the conversation.
Yes, and an intermittent fault is often harder to trace than one that stays present, which is a reason to report it before it becomes a full failure. A connection that works most of the time but drops under load, or a breaker that trips occasionally rather than every time, still points to something that needs attention. We approach an intermittent problem with a broader diagnostic sweep to catch what a quick check might miss.
We power your home. We protect your circuits. We earn the call.
You do not need to know what is wrong before you call. Describing what you are seeing is enough. We talk through it on the phone, scope the job, and confirm the rate before anything is scheduled.
Call (475) 366-2995 every day from 7 AM to 10:30 PM.
View our list of communities. Electrical service reaches these neighboring areas too: West Haven, East Haven, North Haven.
Every electrical job we take on starts with a clear scope and a price confirmed before any work begins. The table below covers the services we handle most often across New Haven and the surrounding area, what each one involves, and who it fits best. Whether you are dealing with a fault that showed up overnight or planning an upgrade you have been putting off, this gives you a plain-language starting point before you call.
| Type of Work | What's Included | Best For | What to Keep in Mind |
|---|---|---|---|
| Electrical Panel UpgradesMost Popular | 100-to-200 amp service upgradesFuse box to breaker panel conversionSubpanel installationLoad calculation before work begins | Older homes with undersized service, or any property adding significant new electrical load | Panel replacements require a permit and inspection in Connecticut. We factor that into the scope and price on the call so nothing is left open-ended. |
| Electrical Repairs & Troubleshooting | Fault tracing from symptom to sourceOutlet and switch testingCircuit and panel checksRepair once cause is confirmed | Any home or property with an unexplained electrical problem | The fault is traced before anything is replaced, so you are not paying for parts that were not the problem. |
| Electrical Safety Inspections | Panel condition and circuit loading reviewOutlet and switch function testingGFCI and AFCI coverage checkGrounding and bonding assessment | Buyers, sellers, landlords, and homeowners who want a clear picture of their system | An inspection identifies what needs attention and explains why, with the scope of any follow-up work priced before it starts. |
Call (475) 366-2995 to talk through what you are seeing and get a price before anything is scheduled.
(475) 366-2995